Rainbow-electronics MAX5929 Manual de usuario descargar pdf (Pagina 1)

General Description

The MAX5927/MAX5929 +1V to +13.2V quad hot-swap

controllers provide complete protection for multisupply

systems. They allow the safe insertion and removal of cir-

cuit cards into live backplanes. These devices hot swap

multiple supplies ranging from +1V to +13.2V, provided

one supply is at or above +2.7V and only one supply is

above +11.0V. The input voltage rails (channels) can be

configured to sequentially turn-on/off, track each other,

or have completely independent operation.

The discharged filter capacitors of the circuit card pro-

vide low impedance to the live backplane. High inrush

currents from the backplane to the circuit card can burn

up connectors and components, or momentarily collapse

the backplane power supply leading to a system reset.

The MAX5927/MAX5929 hot-swap controllers prevent

such problems by gradually ramping up the output volt-

age and regulating the current to a preset limit when the

board is plugged in, allowing the system to stabilize

safely. After the startup cycle is complete, on-chip com-

parators provide VariableSpeed/BiLevel™ protection

against short-circuit and overcurrent faults, and provide

immunity against system noise and load transients. The

load is disconnected in the event of a fault condition. The

MAX5929A automatically restarts after a fault condition,

while the MAX5929L must be unlatched. The MAX5927

fault management mode is selectable.

The MAX5927/MAX5929 offer a variety of options to

reduce external component count and design time. All

devices integrate an on-board charge pump to drive

the gates of low-cost external N-channel MOSFETs, an

adjustable startup timer, and an adjustable current limit.

The devices offer integrated features like startup cur-

rent regulation and current glitch protection to eliminate

external timing resistors and capacitors. The

MAX5929_L provides an open-drain active-low status

output for each channel, the MAX5929_H provides an

open-drain active-high status output for each channel,

and the MAX5927 status output polarity is selectable.

The MAX5927 is available in a 32-pin thin QFN package

and the MAX5929 is available in a 24-pin QSOP pack-

age. All devices are specified over the extended tem-

perature range, -40°C to +85°C.

Applications

Features

♦ Safe Hot Swap for +1V to +13.2V Power Supplies

with Any Input Voltage (V

IN_

≥ 2.7V and Only One

IN_

> 11.0V)

♦ Adjustable Circuit Breaker/Current-Limit

Threshold from 25mV to 100mV

♦ Configurable Tracking, Sequencing, or

Independent Operation Modes

♦ VariableSpeed/BiLevel Circuit-Breaker Response

♦ Internal Charge Pumps Generate N-Channel

MOSFET Gate Drives

♦ Inrush Current Regulated at Startup

♦ Autoretry or Latched Fault Management

♦ Programmable Undervoltage Lockout

♦ Status Outputs Indicate Fault/Safe Condition

MAX5927/MAX5929

Low-Voltage, Quad, Hot-Swap

Controllers/Power Sequencers

________________________________________________________________ Maxim Integrated Products 1

LIM1

ON1

ON2

POL

MODE

ON3

ON4

25 LIM2

STAT2

TIM

N.C.

LATCH

STAT3

STAT4

BIAS

16GND

GATE3

SENSE3

IN3

N.C.

LIM3

GATE2

SENSE2

STAT1

GATE4

SENSE4

IN4

LIM4

GATE1

SENSE1

MAX5927

THIN QFN

1IN1

24 IN2

TOP VIEW

Pin Configurations

Ordering Information

19-2945; Rev 0; 8/03

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

EVALUATION KIT

AVAILABLE

PART TEMP RANGE PIN-PACKAGE

MAX5927ETJ -40°C to +85°C 32 Thin QFN-EP**

MAX5929LHEEG* -40°C to +85°C 24 QSOP

MAX5929LLEEG* -40°C to +85°C 24 QSOP

MAX5929AHEEG* -40°C to +85°C 24 QSOP

MAX5929ALEEG* -40°C to +85°C 24 QSOP

VariableSpeed/BiLevel is a trademark of Maxim Integrated

Products, Inc.

PCI Express Hot Plug

Hot Plug-In Daughter Cards

RAID

Power-Supply

Sequencing/Tracking

Basestation Line Cards

Portable Computer Device

Bays (Docking Stations)

Network Switches, Routers,

Hubs

Selector Guide and Typical Operating Circuit appear at end

of data sheet.

*Future product—contact factory for availability.

**EP = Exposed paddle.

Pin Configurations continued at end of data sheet.

1 2 3 4 5 6 ... 24 25

Indice de contenidos

Pagina 1 - Controllers/Power Sequencers

General DescriptionThe MAX5927/MAX5929 +1V to +13.2V quad hot-swapcontrollers provide complete protection for multisupplysystems. They allow the safe

Pagina 2

MAX5927/MAX5929The MAX5927/MAX5929 turn off all channels if any ofthe above conditions are not met. After a fault-latchedshutdown, cycle any of the ON

Pagina 3

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers________________________________________________________________________________

Pagina 4

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers12 _____________________________________________________________________________

Pagina 5

The MAX5927/MAX5929 turn off all channels if any ofthe above conditions are not met. After a fault-latchedshutdown, cycle any of the ON_ inputs to unl

Pagina 6

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers14 _____________________________________________________________________________

Pagina 7

Slow-Comparator Startup PeriodThe slow comparator is disabled during the startupperiod while the external MOSFETs are turning on.Disabling the slow co

Pagina 8

MAX5927/MAX5929age. tD,UVLOensures that the board is fully insertedinto the backplane and that the input voltages are stable. The MAX5927/MAX5929 incl

Pagina 9

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers________________________________________________________________________________

Pagina 10

MAX5927/MAX5929Sense ResistorThe slow-comparator threshold voltage is adjustablefrom 25mV to 100mV. Select a sense resistor that caus-es a drop equal

Pagina 11

Startup SequenceThere are two ways of completing the startupsequence. Case A describes a startup sequence thatslowly turns on the MOSFETs by limiting

Pagina 12

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers2 ______________________________________________________________________________

Pagina 13

MAX5927/MAX5929With a 22nF gate capacitor, the inrush current, charge,and discharge times are:Case B: Fast Turn-On (With Current Limit)In applications

Pagina 14

The maximum inrush current in this case is:Figure 6 shows the waveforms and timing diagrams fora startup transient with current regulation (see theTyp

Pagina 15

MAX5927/MAX5929Layout ConsiderationsTo take full tracking advantage of the switch responsetime to an output fault condition, it is important to keep a

Pagina 16

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers________________________________________________________________________________

Pagina 17

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers24 _____________________________________________________________________________

Pagina 18

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power SequencersMaxim cannot assume responsibility for use of any circuitry other than circuitry

Pagina 19

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers________________________________________________________________________________

Pagina 20

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers4 ______________________________________________________________________________

Pagina 21

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers________________________________________________________________________________

Pagina 22

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers6 ______________________________________________________________________________

Pagina 23

XXXXMAX5927toc19VINW2V/div0VVONW2V/div0V5V/div0V4ms/divVGATEXVGATEWVPWRRDYTURN-OFF INVOLTAGE-TRACKING MODEXXXXMAX5927toc20VINW2V/divVONW2V/div0V5V/div

Pagina 24

MAX5927/MAX5929Low-Voltage, Quad, Hot-SwapControllers/Power Sequencers8 ______________________________________________________________________________

Pagina 25 - QSOP.EPS

Detailed DescriptionThe MAX5927/MAX5929 are circuit-breaker ICs for hot-swap applications where a line card is inserted into alive backplane. The MAX5

Comentarios a estos manuales

Sin comentarios

Rainbow-electronics MAX5929 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Rainbow-electronics MAX5929. Rainbow Electronics MAX5929 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Rainbow-electronics MAX5929 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Rainbow-electronics MAX5929. Rainbow Electronics MAX5929 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Rainbow-electronics MAX5929