Rainbow-electronics MAX5419 Manual de usuario descargar pdf (Pagina 4)

MAX5417/MAX5418/MAX5419

256-Tap, Nonvolatile, I

C-Interface,

Digital Potentiometers

4 _______________________________________________________________________________________

Note 1: The DNL and INL are measured with the potentiometer configured as a voltage-divider with H = V

and L = GND. The

wiper terminal is unloaded and measured with a high-input-impedance voltmeter.

Note 2: The DNL and INL are measured with the potentiometer configured as a variable resistor. H is unconnected and L = GND.

For the 5V condition, the wiper terminal is driven with a source current of 80µA for the 50kΩ configuration, 40µA for the

100kΩ configuration, and 20µA for the 200kΩ configuration. For the 3V condition the wiper terminal is driven with a source

current of 40µA for the 50kΩ configuration, 20µA for the 100kΩ configuration, and 10µA for the 200kΩ configuration.

Note 3: The wiper resistance is measured using the source currents given in Note 2.

Note 4: The device draws current in excess of the specified supply current when this input is driven with a voltage greater than 0.7

x V

. This is due to the complementary metal-oxide semiconductor (CMOS) shunt current (P- and N-channel output

devices on simultaneously).

Note 5: Wiper at midscale with a 10pF load. Potentiometer set to midscale, L = GND, an AC source is applied to H, and the output

is measured as 3dB lower than the DC W/H value in dB.

Note 6: The programming current operates only during power-up and NV writes.

Note 7: SCL clock period includes rise and fall times t

and t

. All digital input signals are specified with t

= t

= 2ns and timed

from a voltage level of (V

+ V

) / 2.

Note 8: Wiper settling time is the worst-case 0% to 50% rise time measured between consecutive wiper positions. H = V

L = GND, and the wiper terminal is unloaded and measured with a 10pF oscilloscope probe (see the Typical Operating

Characteristics for the tap-to-tap switching transient).

Note 9: An appropriate bus pullup resistance must be selected depending on board capacitance. Refer to the document linked to

this web address: www.semiconductors.philips.com/acrobat/literature/9398/39340011.pdf

Note 10: The idle time begins from the initiation of the stop pulse.

PARAMETER

SYMBOL

CONDITIONS

MIN TYP MAX

UNITS

Data Setup Time

SU-DAT

100 ns

Data Hold Time

HD-DAT

0 0.9 µs

SDA, SCL Rise Time t

300 ns

SDA, SCL Fall Time t

300 ns

Setup Time for STOP Condition

SU-STO

0.6 µs

Bus Free Time Between STOP

and START Condition

BUF

Minimum power-up rate = 0.2V/ms 1.3 µs

Pulse Width of Spike Suppressed

50 ns

Maximum Capacitive Load for

Each Bus Line

(Note 9) 400 pF

Nonvolatile Store Time

Idle time required after a nonvolatile

memory write (Note 10)

30 ms

TIMING CHARACTERISTICS (continued)

= +2.7V to +5.25V, H = V

, L = GND, T

= -40°C to +85°C, unless otherwise noted. Typical values are at V

= +5V, T

+25°C. See Figures 1 and 2.) (Note 7)

1 2 3 4 5 6 7 8 9 ... 13 14

Comentarios a estos manuales

Sin comentarios

Rainbow-electronics MAX5419 Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Rainbow-electronics MAX5419